Asee peer logo
Displaying all 10 results
Conference Session
Division Experimentation & Lab-oriented Studies: Mechanical Engineering and Control
Collection
2015 ASEE Annual Conference & Exposition
Authors
Roger A Beardsley PE, Central Washington University
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
pump driven by an air motor, shown in Figure 9.The gear pump is a constant volume device. Theory predicts that if driven at twice the speed,twice the volume flow rate would be produced regardless of pumping pressure. In reality theincrease in pressure leads to internal leakage, which is reflected as a reduction in volume-per-revolution in the data and graphed. The inlet suction pressure also varies with the flow rate dueto fluid friction in the inlet hose. This lab investigates both the pump internal leakage rates andthe tubing pressure loss.In performing this experiment, an air motor turns the gear pump. At the pump outlet is a ballvalve that creates a restriction and thus a pumping load. A rotameter is used for measuringvolume flow rate of
Conference Session
Division Experimentation & Lab-Oriented Studies: Bring-Your-Own-Experiments 1
Collection
2015 ASEE Annual Conference & Exposition
Authors
Rebecca Marie Reck, University of Illinois, Urbana-Champaign
Tagged Topics
Diversity
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
wereapproximately 75 students enrolled in the course during the first run. One lecture section isoffered each semester of the first run. To measure the effectiveness of each type of equipment,both qualitative and quantitative data are being collected from the students. The quantitative datacollected included exam scores, laboratory report scores, concept inventory, and satisfactionsurvey. The concept inventory was based on the test by Bristow et al. 11 The qualitative dataincludes laboratory observation and student reflections included in their individual laboratoryreports. The data between the two groups were analyzed for differences in overall courseperformance as well as the attainment of the objectives listed in the experiments above
Conference Session
Division Experimentation & Lab-Oriented Studies: Pedagogy of Lab-Oriented Courses
Collection
2015 ASEE Annual Conference & Exposition
Authors
Bridget M. Smyser, Northeastern University; Gregory J Kowalski, Northeastern University; Andrew F. Carbonar, Northeastern University
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
strongcollaboration with an individual lab instructor, as even the best experimental apparatus will notbe used if an instructor does not see the value of incorporating it into their course. It also seemsthat teams who incorporate pedagogical research produce more sophisticated apparatus from adesign perspective. Finally, reflections of the students involved in the development of theseexperiments are examined in order to gain insight into how students perceive and usepedagogical information in their designs.IntroductionIt has been established by a number of authors that laboratory experiments and experimentalapparatus can be effectively designed by undergraduate students. There are a number of reasonsto use undergraduate students to create lab experiments
Conference Session
Best Paper Presentations
Collection
2015 ASEE Annual Conference & Exposition
Authors
Eric Constans, Rowan University; Shivakumar I Ranganathan, Rowan University; Wei Xue, Rowan University
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
. The planetary gearset is the centerpiece of thebench-scale hybrid powertrain, which our students are completing over the course of fivesemesters. With the successful completion of the planetary gearset, our students are now readyto begin tackling the challenge of developing an overall control strategy for the hybrid system.AcknowledgementsThe authors wish to acknowledge the support of the NSF-TUES program in the Division ofUndergraduate Education, DUE-1044532, which made this research possible. Any opinions,findings, and conclusions or recommendations expressed in this material are those of the authorsand do not necessarily reflect the views of the National Science Foundation.Bibliography[1] Toyota Motor Corporation, "Toyota Hybrid
Conference Session
Division Experimentation & Lab-oriented Studies: Mechanical Engineering and Control
Collection
2015 ASEE Annual Conference & Exposition
Authors
Julianne Vernon, University of Michigan, College of Engineering; Cynthia J. Finelli, University of Michigan; Noel C. Perkins, University of Michigan; Bradford G Orr, University of Michigan
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
students computed the potential energy due to gravity (requiring firstnumerically integrating the angular velocity data), and then the total mechanical energy (sum ofkinetic and potential energies). That sum immediately reveals that the mechanical energydecreases with each cycle (Fig. A2(b)). We further asked our students to reflect on thisexperimental fact and to propose the mechanism(s) responsible for this dissipation. Thisnaturally led them to the phenomenon of rolling resistance of tires and the real (adverse) effectsthat rolling resistance has on vehicle energy consumption and greenhouse gas emissions! Thepoint is that the four often-misunderstood concepts concerning the dynamics of rigid bodies werereadily captured in this simple in-class
Conference Session
Division Experimentation & Lab-Oriented Studies: Bring-Your-Own-Experiments 2
Collection
2015 ASEE Annual Conference & Exposition
Authors
Jun Nogami, University of Toronto; Scott Ramsay, University of Toronto; Scott D Ramsay, University of Toronto
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
volunteered likely felt strongly oneway or the other about the experiment. In the future, the authors will consider administering theMCI to the same students before and after the experiment. Page 26.313.11In addition, the experiment guide distributed to students will be altered. Though the guide willnot be collected for grades, additional open-ended questions will be posed. This will give thestudents the opportunity to better reflect on what they have learned and may likely improve theconceptual results of the experiment.Finally, the MCI is multiple choice and therefore not necessarily the best method to showconceptual understanding. In addition to
Conference Session
Division Experimentation & Lab-Oriented Studies: Pedagogy of Lab-Oriented Courses
Collection
2015 ASEE Annual Conference & Exposition
Authors
Nebojsa I Jaksic P.E., Colorado State University, Pueblo
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
learning objectives. Also, designemphasis (cognitive objective) and proficiency with 3D-printing processes (skill learningobjective) are reflected in ABET General Criterion 3, Student Outcomes23 (c) “an ability todesign a system, component, or process to meet desired needs within realistic constraints such aseconomic, environmental, social, political, ethical, health and safety, manufacturability, andsustainability” and (k) “an ability to use the techniques, skills, and modern engineering toolsnecessary for engineering practice.” In addition, physical models that provide tactile, visual, andmanipulative feedback to learners have been implemented successfully in general education for along time.The 3D-printing lab includes nine inexpensive 3D
Conference Session
Division Experimentation & Lab-oriented Studies: Electrical and Computer Engineering Labs
Collection
2015 ASEE Annual Conference & Exposition
Authors
Kip D. Coonley, Duke University; Justin Miles, Duke University
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
%), Acceptance (84%), Relationship toAccreditation Board of Engineering Technology (ABET) Student Outcomes (94%), andRelationship to Course Objectives (91%). In addition, despite the slower upload speed of theBeagleboard-xM, the total amount of time required to complete DSP hardware-basedlaboratories using the Beagleboard-xM was reduced by 6.6%. Further, and perhaps mostencouraging, is that results suggest even a one-time lab experience with the Beagleboard isenough to overcome any learning curve it might have and thus accelerate lab completion.Finally, comments and feedback solicited from students and teaching assistants reflect positively Page
Conference Session
Division Experimentation & Lab-oriented Studies: Electrical and Computer Engineering Labs
Collection
2015 ASEE Annual Conference & Exposition
Authors
Valentin Siderskiy, NYU Polytechnic School of Engineering; Aatif Ahmed Mohammed, NYU Polytechnic School of Engineering; Vikram Kapila, NYU Polytechnic School of Engineering
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
. IEEE Trans. Edu., 49(3):389–397, 2006.[24] J. Ma and L Jeffrey. Hands-on, simulated, and remote laboratories: A comparative literature review. ACM Computing Surveys, 38(3), 1–24, 2006.[25] R.M. Felder and L.K. Silverman. Learning and teaching styles in engineering education. Engineering Education, 78(7):674–681, 1988.[26] N.D. Fleming and C. Mills. Not another inventory, rather a catalyst for reflection. To Improve the Academy, 11: 137–155, 1992. Page 26.348.15
Conference Session
Division Experimentation & Lab-oriented Studies: Mechanical Engineering and Control
Collection
2015 ASEE Annual Conference & Exposition
Authors
Jason Yao, East Carolina University
Tagged Divisions
Division Experimentation & Lab-Oriented Studies
. b) Modify the house parameters in the m.file to reflect the provided dimensions of the incubator. Save all the changes. After this file is run, the values of all the parameters will be in the MATLAB workspace and SIMULINK can use these values in the model built next. c) Build the incubator model in SIMULINK, using thermal parameters defined in the .m file. The subsystem should have two inputs: heat (power) flowing in “Qin” and the outside temperature “Tout”; one output: the air temperature in the incubator “Tincub”. Mask the model as a subsystem. d) Add the calculation of the bulb parameters Rf, Rb, Cf, Cb, and ReqBulb into the same