Conference Session

Assessment Methods and Learning Pedagogy I

Collection

2011 ASEE Annual Conference & Exposition

Authors

Mehrube Mehrubeoglu, Texas A&M University, Corpus Christi; Satyajit Verma, Texas A&M University, Corpus Christi

Tagged Divisions

Engineering Technology

along the skill subsets (a – k criteria), and presents them to the Page 22.1309.2accreditation agency for evaluation. A presentation such as this for accreditation evaluation canbe seen as circumstantial, inferential and relies heavily on the perception of evaluators. In orderto counter such perception-based evaluation, it can be proposed that because the performance ofstudents in each course is already quantified as an integral element of their education, suchquantification should, therefore, be carried over to the evaluation process of education itself.The element of intuitive evaluation in the program evaluation process cannot and should

Conference Session

ETD Internet of Things (IOT)

Collection

2017 ASEE Annual Conference & Exposition

Authors

Shuning Li, Indiana University-Purdue University Indianapolis; Elizabeth Freije, Indiana University-Purdue University, Indianapolis; Paul Yearling P.E., Indiana University-Purdue University, Indianapolis

Tagged Divisions

Engineering Technology

engineering problems. The objective of the project is to design and develop an IoTapplication to remote monitor the performance of a RepRap 3D printer including the printingprogress and the temperatures of the heated bed and hot end. Major tasks involved in the projectare: to inspect and upgrade the current 3D printer to avoid any possible compliance issuesbetween the 3D printer and the hardware components or software tools for the IoT application; toconnect the 3D printer to the Raspberry Pi microprocessor; and to design and develop the IoTapplication.The methods and algorithms of connecting a 3D printer to an IoT application is reported, and theIoT application interface and workflow will be presented in the results section. As a pilot study,this

Conference Session

Mechatronics

Collection

2017 ASEE Annual Conference & Exposition

Authors

John R. Haughery, Iowa State University; D. Raj Raman, Iowa State University; Amy L. Kaleita, Iowa State University; Steven A. Freeman, Iowa State University

Tagged Divisions

Engineering Technology

, the overarching goal of his teaching is to impart the core content needed by the students, and to do so while encouraging inquisition and higher levels of thought. He has secured com- petitive funds to support his teaching efforts – from university, industry, and federal sources – and for his efforts has received departmental, college, and national teaching honors including the Farrall Young Edu- cator Award (2004) and the Massey-Ferguson Gold Medal Teaching Award (2016) given by the American Society of Agricultural Engineers. He has also been an invited participant in the National Academy of Engineering’s 2013 Frontiers in Engineering Education Conference. Raman chairs the ABE Engineering Curriculum Committee and

Conference Session

A Technology Potpourri II

Collection

2019 ASEE Annual Conference & Exposition

Authors

Maher Shehadi, Purdue Polytechnic Institute

Tagged Divisions

Engineering Technology

Paper ID #25045Students’ Responses to Flipping Applied Fluids from Instructor-centered toStudent-centered Using Problem-based Learning ParadigmDr. Maher Shehadi, Purdue Polytechnic Institute Dr. Shehadi is an Assistant Professor of Mechanical Engineering Technology (MET) at Purdue Univer- sity. His academic experiences have focused on learning and discovery in areas related to HVAC, indoor air quality, human thermal comfort, and energy conservation. While working with industry, he oversaw maintenance and management programs for various facilities including industrial plants, high rise residen- tial and commercial buildings

Conference Session

STEM Issues

Collection

2019 ASEE Annual Conference & Exposition

Authors

Otilia Popescu, Old Dominion University; Vukica M. Jovanovic, Old Dominion University; Krishnanand Kaipa, Old Dominion University; Karina Arcaute, Old Dominion University; Anthony W. Dean, Old Dominion University

Tagged Topics

Diversity

Tagged Divisions

Engineering Technology

in academia. He is currently Assistant Dean for Research, Batten College of Engineering and Technology (BCET) at ODU. His previous appointments include As- sociate Professor of Engineering Technology and as Associate Director of the Institute for Ship Repair, Maintenance, and Operations at Old Dominion University (ODU).His research has focused mostly on control systems (integration and testing) and the reliability and maintainability of complex systems. He has been selected as both a NASA and an ONR Faculty Fellow. He regularly teaches courses in Ma- rine Engineering and in Maintained Systems. Most recently Dr. Dean was on the Headquarters Staff the American Society of Naval Engineers. He received his Ph.D. from

Conference Session

Electrical and Computer Engineering Technology Projects and Applications

Collection

2011 ASEE Annual Conference & Exposition

Authors

Chandra R. Sekhar, Purdue University, Calumet ; Omer Farook, Purdue University; Jai P. agrawal, Purdue University Calumet; Essaid Bouktache, Purdue University, Calumet

Tagged Divisions

Engineering Technology

the curriculum of an Electrical and Computer EngineeringTechnology program, the biomedical course is redesigned so that the students can follow thetheory with laboratory experiments for processing biomedical signals utilizing System DesignApproach (SDA). Isolated experiments focused on a single topic never conveyed the holistic feelthat is gained through a complete instrumentation platform design.This course is offered in the form of Learning Modules. The paper discuses the coursesystem design learning modules which encompasses: 1) Bio signal, Transducers and SignalConditioning, 2) Microcontrollers based Embedded System design, 3) Embedded SystemProgramming, 4) Object-Oriented Programming (OOP) Design, 5) Use of Graphical UserInterface (GUI

Conference Session

Assessment Methods and Learning Pedagogy II

Collection

2011 ASEE Annual Conference & Exposition

Authors

Jyhwen Wang, Texas A&M University; Alex Fang, Texas A&M University; Michael Ryan Golla, Texas A&M University

Tagged Divisions

Engineering Technology

, and lecture-lab timing is suggested.References1. Krupezak, J., Disney, K., and VanderStoep, S., “Laboratory projects appropriate for non-engineers and introduction to engineering.” 2009 Annual Conference and Exposition, 2009-603, American Society for Engineering Education.2. Sinba, A., “Engineering laboratory experiments – an integrated approach of teaching the introductory engineering course,” 2007 Annual Conference and Exposition, 2007-189, American Society for Engineering Education.3. Dekker, D., “Recent developments in mech lab I at the university of south florida,” 2007 Annual Conference and Exposition, 2007-410, American Society for Engineering Education.4. Salehpour, A., and Antoline, S., “Rapid prototyping as an

Conference Session

Engineering Technology Pedagogy 1

Collection

2021 ASEE Virtual Annual Conference Content Access

Authors

Rungun Nathan, Pennsylvania State University

Tagged Divisions

Engineering Technology

Haptics and Virtual Reality. His research interests are in the areas of unmanned vehicles particularly flapping flight and frisbees, mechatronics, robotics, MEMS, virtual reality, and haptics, and teaching with technology. He has ongoing research in flapping flight, Frisbee flight dynamics, lift in porous material and brain traumatic injury He is an active member of APS (DFD), ASEE and ASME and reviewer for several ASME, IEEE and ASEE, FIE conferences and journals. American c Society for Engineering Education, 2021 Computer Interfacing to Real world: A Low-Cost ApproachAbstractThis paper is about how to interface the real world to a computer. Using a low

Conference Session

Simulations and Project-Based Learning II

Collection

2014 ASEE Annual Conference & Exposition

Authors

Ying Lin, Western Washington University; Ed Moran, Western Washington University; Jeremy Ruhland, Western Washington University

Tagged Divisions

Engineering Technology

cover antenna theory, RF signal propagation modeling, and communication systems which are fundamental in upper-division EE/EET curriculum. The system renders several promising features: portable, low-cost, simple, and compact in size, to name a few. In this paper, we first introduce the components and the mechanism of the RF measurement system. We then present a laboratory exercise that designed for an antenna radiation pattern study using the developed system. Detailed lab procedures and results collected from a recent upper-division communication systems course in an EET program are provided. The lab results demonstrate the effectiveness of the developed system. Additional assessment data from students’ feedback further

Conference Session

ETD Design I: Electrical and Computer Engineering Technology

Collection

2011 ASEE Annual Conference & Exposition

Authors

Antonio Soares, Florida A&M Univeristy; Chao Li, Florida A&M University/Florida State University

Tagged Divisions

Engineering Technology

until November 2003. Antonio started his pursuit of the Doctor of Philosophy degree at the Florida Agricultural and Mechanical University in January 2004 under the supervision of Dr. Reginald Perry. Upon completion of his PhD, Dr. Soares was immediately hired as an assistant professor (Tenure Track) in the Electronic Engineering Technology department at FAMU. Dr. Soares has made many contributions to the department, from curriculum improvements, to ABET accreditation, and more recently by securing a grant with the department of education for more than half a million dollars.Chao Li, Florida A&M University/Florida State University Dr. Chao Li is currently working at Florida A&M University as an assistant

Conference Session

Computer ET Innovation

Collection

2008 Annual Conference & Exposition

Authors

David Forsman, Pennsylvania State University-Erie

Tagged Divisions

Engineering Technology

formthat the student could re-play over and over? Could student-instructor interaction be handledelectronically in an effective manner?One of the concerns related to e-learning might be the loss of the tangential “information” thatwould be lost with a decrease in face to face time with the students. How does one get impressupon the student the value of ethics and academic integrity related to the engineering professionthat is not specifically stated in the course outline, yet come up in class numerous times duringthe semester? Case in point would be the issue of simply filling in the summary sheet forcoupled assignments with duplicate information rather than going back though thedocumentation to enter the computed values. Being sloppy in this

Conference Session

Capstone/ET Projects III - Mechanical and Manufacturing Focus

Collection

2020 ASEE Virtual Annual Conference Content Access

Authors

Immanuel Edinbarough P.E., University of Texas Rio Grande Valley; Aditya Akundi, University of Texas Rio Grande Valley

Tagged Topics

Diversity

Tagged Divisions

Engineering Technology

field, the Department of Manufacturing and Industrial Engineering provides asetting for technology development and applied research in the Engineering Technology (ENGT)program. According to the program description, engineering technology education emphasizesprimarily on the applied aspects of science and product improvement, industrial practices, andengineering operational functions. A capstone two-semester senior project course is a part of theengineering technology curriculum. This course provides the students an opportunity to addressand experience the critical problems faced in the day-to-day life of an engineer in an advancedmanufacturing industry. One such problem is to find a quick replacement for the damagedcritical part that limits the

Conference Session

A Technology Potpourri I

Collection

2019 ASEE Annual Conference & Exposition

Authors

Jorge Crichigno, University of South Carolina; Sadia Ahmed, Northern New Mexico College; John H. Gerdes, University of South Carolina; Robert G. Brookshire, University of South Carolina

Tagged Topics

Diversity

Tagged Divisions

Engineering Technology

marketable skills.2. Project Goals and Tasks The project has multiple goals, as presented next. Goal 1: Establish and integrate a cybersecurity curriculum into the bachelor degrees in IT at USC and NNMC.The programs follow the philosophy of the Wright State Model (WSM)1 of Education. While theyare technology programs, students are required to take math and science up to calculus I. The taskssupporting Goal 1 include: Tasks for Goal 11.1 Create a new cybersecurity core course and implement major modifications in an existing course, which will become the second cybersecurity core course.1.2 Enhance a pre-requisite course by infusing cybersecurity content.1.3 Incorporate an internship experience in

Conference Session

ET Pedagogy I

Collection

2019 ASEE Annual Conference & Exposition

Authors

Mohammad Moin Uddin P.E., East Tennessee State University; Peter D. Rogers, Georgia Southern University; Christopher David Leblanc, University of New Hampshire; Keith V. Johnson, East Tennessee State University

Tagged Divisions

Engineering Technology

Paper ID #25124Pedagogical Risk Taking: Is It Worth It?Dr. Mohammad Moin Uddin P.E., East Tennessee State University Dr. Mohammad Moin Uddin is an associate professor in the Department of Engineering, Engineering Technology, and Surveying at East Tennessee State University. He holds a joint appointment as an As- sociate Professor of Engineering and Engineering Technology and as a Graduate Faculty member of the Graduate Studies. Dr. Uddin is active in research and scholarship. He has been awarded grants from National Science Foundation, Tennessee Department of Transportation, DENSO and ASEE (ETD mini- grants) and

Conference Session

Project-Based Student Learning: Part II

Collection

2009 Annual Conference & Exposition

Authors

Dale Litwhiler, Pennsylvania State University, Berks; Frances Jallu, Pennsylvania State University, Berks

Tagged Divisions

Engineering Technology

data could then bedownloaded for use in engineering technology classes to help demonstrate the operation ofequipment powered by solar energy and rechargeable batteries. Incorporating real-world solarpower projects into engineering curriculum has been presented by others. 2,3,4System Design and ConstructionFigure 2 shows a block diagram of the bus shelter custom audio system. The solar panel isconstructed of thin-film amorphous silicon and produces an operating voltage of 7.2V at 100mA.The battery is a 6V, 1.2Ah sealed lead acid deep-discharge battery. The amplifier and speakersare very inexpensive consumer electronic devices typically used with an MP3 player to listen tomusic without using headphones. Figure 2

Conference Session

Industry and Engineering Technology Partnerships

Collection

2008 Annual Conference & Exposition

Authors

Joseph Fuehne, Purdue University-Columbus

Tagged Divisions

Engineering Technology

College of Technology decided to implement the class. An outline of the class withdesired objectives was submitted to the curriculum committee of the MET department andapproved as a “Special Topics in MET” class. The class was offered with no prerequisite classesand approved as a technical selective for the two-year associate of science degree in MET.Employees from local industry as well as current students in MET were encouraged to registerfor the class. This class has been conducted during the fall semester in 2005, 2006 and 2007,serving over 40 students.This work details the organization of the class including objectives, hands-on activities,assessments, and course materials. Basically, the Book of Knowledge2 published by the ASQ

Conference Session

TC2K Methods and Models

Collection

2007 Annual Conference & Exposition

Authors

Gregory Watkins, University of North Carolina-Charlotte; Nan Byars, University of North Carolina-Charlotte; Deborah Sharer, University of North Carolina-Charlotte

Tagged Divisions

Engineering Technology

continuing education.In addition to laying out requirements for assessment, the criteria document also requiresprograms to demonstrate that assessment results are used in a formal continuous improvementprocess to further develop the program.Assessment AcronymsThe MET program utilizes the centralized assessment process provided by the college ofengineering (COE). The COE first began an integrated process of strategic planning,measurement, evaluation, and feedback in 1992, with the purpose of identifying continuousimprovement opportunities. The principal components and their interactions are summarized inthe Assessment Triad shown in Figure 1. Figure 1 – Assessment TriadAs illustrated above, the continuous improvement

Conference Session

Capstone Projects and Experiential Learning

Collection

2011 ASEE Annual Conference & Exposition

Authors

Chip W. Ferguson, Western Carolina University; Phillip A. Sanger, Western Carolina University

Tagged Divisions

Engineering Technology

integrated PBL curriculum to address this need. Additionally, the “soft skills” learningthat have been previously presented during the capstone sequence will now be delivered in thePBL curriculum. We have learned that faculty mentors are key role players in achieving successwith the project in terms of meeting the learning outcomes. The faculty member has to develop abalance between meeting the needs of the customer, a completed product, and the experimentallearning that must take place over the course of the project. Finally, student teams who engagethe customer frequently throughout the progression of the project meet the requirements of theproject more frequently. The 2010-2011 capstone year now requires faculty and industry mentorsto meet one

Conference Session

ET Pedagogy II

Collection

2020 ASEE Virtual Annual Conference Content Access

Authors

Vigyan Jackson Chandra, Eastern Kentucky University

Tagged Divisions

Engineering Technology

, networking, communication systems, along with digital, analog, and machine-control electronics. He is the recipient of the 2013 Golden Apple Award for Teaching Excellence at Eastern and has been nominated multiple times for the Critical Thinking Teacher of the Year Award. His professional interests include implementing active teaching and learning strategies, metacognition, integrating open-source software/hardware with online control, and deploying electrical and telecom technologies in community-based organizations. He is always seeking opportunities for collaborating on teaching, scholarly, and service projects, especially those aimed at improving students’ critical/creative and communication skills

Conference Session

Capstone and Senior Design Projects Session

Collection

2013 ASEE Annual Conference & Exposition

Authors

Martin William Weiser, Eastern Washington University; Hani Serhal Saad, Eastern Washington University; N.M. Awlad HOSSAIN, Eastern Washington University

Tagged Divisions

Engineering Technology

tostructure both pedagogical materials and assessment rubrics to improve the capstone experiencesfor senior design students.Bannerot et al. [3] identified some of the issues and their resolution associated with thedevelopment and implementation of a new, one-semester, interdepartmental, multidisciplinarycapstone design course involving the seniors from four engineering programs at the University ofHouston. The revised course curriculum incorporated the usage of website to enhanceinformation transfer, use cohorts to modularize the large number of students and teams, use astudio/critique teaching format, integrate communications professionals into the teaching of thecourse, and allow students to be involved in establishing the final expectations for

Conference Session

Electrical ET Projects and Applications

Collection

2006 Annual Conference & Exposition

Authors

Brian Perry, Bloomsburg University; Michael Williams, Bloomsburg University; Scott Eckert, Bloomsburg University; Biswajit Ray, Bloomsburg University

Tagged Divisions

Engineering Technology

University of Pennsylvania. He also serves as the Coordinator of the EET program. Page 11.341.2 Computer-Based Instrumentation ProjectsAbstractStudent-initiated projects as part of an instrumentation and data acquisition course forsophomore-level electronics engineering technology students are presented. The threeinstrumentation projects reported in this paper are: an automated parking garage system, anautomated draw-bridge control system, and an intelligent traffic light controller. All threeprojects focused on instrumentation system development integrating multiple sensors andactuators, data acquisition hardware, interface electronics

Conference Session

Professional Development and Scholarship

Collection

2007 Annual Conference & Exposition

Authors

Ahmed Khan, DeVry University; Amin Karim, DeVry University

Tagged Divisions

Engineering Technology

actually be made of these survey results.”• “It is good for us to network with professionals in companies that hire technicians.”• “In my opinion, it is an absolute necessity that technical educators spend time at conferences, workshops, seminars, working in industry, etc. It is very easy to lose touch with technology and industry trends and needs. Advisory Committees can play an important role in curriculum evaluation and development. Since 1998, a large percentage of my graduates have gone to work in "Clean room" environments. I had never been inside a clean room, until this past summer. I was able to spend a week in a clean room and build MEMS devices. Does this experience help me relate to my graduates and soon-to

Conference Session

Manufacturing Capstone and Design Projects

Collection

2007 Annual Conference & Exposition

Authors

Wei Zhan, Texas A&M University; Ben Zoghi, Texas A&M University; Rainer Fink, Texas A&M University

Tagged Divisions

Engineering Technology

AC 2007-819: A COURSE PROJECT WITH A FOCUS ON PRODUCTDEVELOPMENT PROCESSWei Zhan, Texas A&M University Dr. Wei Zhan is an Assistant Professor of Electronics Engineering Technology at Texas A&M University. Dr. Zhan earned his D.Sc. in System Science from Washington University in 1991. From 1991 to 1995 he worked at University of California, San Diego and Wayne State University. From 1995 to 2006, he worked in the automotive industry as a system engineer. In 2006 He joined the Electronics Engineering Technology faculty at Texas A&M. His research activities include control system theory and applications to industry, system engineering, robust design, modeling, simulation

Conference Session

Capstone/ET Projects II - General

Collection

2020 ASEE Virtual Annual Conference Content Access

Authors

Wei Vian, Purdue University, West Lafayette; Nancy L. Denton P.E., Purdue University, West Lafayette

Tagged Divisions

Engineering Technology

designed and weldedthe model bridges they tested. Basic welding knowledge and techniques were introducedand practiced in the freshman-level materials and processes course. Affording studentsthe opportunity to draw on relatively disparate learning from previous courses was thethird implicit instructional goal for the designed beam deflection project. As the studentsprogress toward their senior capstone integrative experience, this small-scale multi-disciplinary project contributes to establishing the learning scaffolding needed to preparethem for the capstone’s broad-based integration of knowledge.[5, 6] This is a greatopportunity to connect the previous course learning and hands-on experience to recentstudy in an applied method.For the designed

Conference Session

Simulation and Virtual Instrumentation

Collection

2011 ASEE Annual Conference & Exposition

Authors

Nikunja Swain, South Carolina State University

Tagged Divisions

Engineering Technology

AcknowledgementThis work was funded in part by a grant from the NSF-HBCU-UP/RISC grant. We are thankful to theNSF for providing us with this help. References1. Swain, N. K., Korrapati, R., Anderson, J. A. (1999) “Revitalizing Undergraduate Engineering, Technology, and ScienceEducation Through Virtual Instrumentation”, NI Week Conference, Austin, TX..2. Elaine L., Mack, Lynn G. (2001), “Developing and Implementing an Integrated Problem-based Engineering TechnologyCurriculum in an American Technical College System” Community College Journal of Research and Practice, Vol. 25, No.5-6, pp. 425-439.3. Buniyamin, N, Mohamad, Z., 2000 “Engineering Curriculum Development: Balancing Employer Needs and

Conference Session

MET Papers 2

Collection

2017 ASEE Annual Conference & Exposition

Authors

Shoji Nakayama, Purdue University Northwest (College of Technology); Ali Alavizadeh, Purdue University Northwest

Tagged Divisions

Engineering Technology

Paper ID #18496Inclusion of Safety Discipline into Pneumatic and Hydraulics Lab ActivitiesDr. Shoji Nakayama, Purdue University Northwest (College of Technology) Dr. Shoji Nakayama is an Associate Professor of Organizational Leadership and Supervision in the De- partment of Construction Science and Organizational Leadership at Purdue University Northwest. In this position, he teaches safety and health related courses, as well as improving Environmental Health and Safety curriculum through Industrial Advisory Committees. Dr. Nakayama has safety related experience in automotive, airline, regulatory agency and printing

Conference Session

ETD Green Energy/Sustainability

Collection

2017 ASEE Annual Conference & Exposition

Authors

Jesse Gilmore, University of Houston, Downtown; Scott Patterson, University of Houston, Downtown; Lisa Deane Morano; Vassilios Tzouanas, University of Houston, Downtown

Tagged Topics

Diversity

Tagged Divisions

Engineering Technology

components of the system is shown in Figure 2. Fig. 2: Block Diagram of UHD Sustainability Garden Automated Irrigation SystemTo collect solar energy, two RENOGY® 250W mono-crystalline black photovoltaic panels areused6 (Figure 3). An Air Primus Air40 wind turbine7 (Figure 4) is used to provide a secondarysource of energy in addition to the solar panels. The wind turbine is mounted to a steel pole at aheight of 23’ and contains an integrated charge controller that allows the wiring to be directlyconnected to the battery bank. It requires a 7 mph wind to begin spinning the turbine blades. Therated output is 160 watts given a 12 mph wind speed.Other major components of the renewable system include the batteries for energy storage (two100 Ah

Conference Session

Multimedia and Distance Learning

Collection

2011 ASEE Annual Conference & Exposition

Authors

Ronald H. Rockland, New Jersey Institute of Technology; Howard S. Kimmel, New Jersey Institute of Technology; John D. Carpinelli, New Jersey Institute of Technology

Tagged Divisions

Engineering Technology

management systems, such as Moodle, have enabled courses to be effectively deliveredin an online format. The features that these systems have can also be effective in a face to faceclassroom, helping both the instructor and the student. This paper has shown several of thesefeatures used in a variety of face to face classes, including laboratory based, lecture based, and asenior capstone design course.References[1] Kyei-Blankson, L., Keengwe, J., Blankson, J. “Faculty Use and Integration of Technology in HigherEducation”, AACE Journal, v17 n3 p199-213 Jul 2009[2] White, C.P., Ramirez, R., Smith, Jessica G., Plonowski, L. “Simultaneous Delivery of a Face-to-Face Course toOn-Campus and Remote Off-Campus Students” TechTrends v. 54 no. 4 (July 2010) p

Conference Session

Capstone and Senior Design Projects Session

Collection

2013 ASEE Annual Conference & Exposition

Authors

Byron G. Garry, South Dakota State University

Tagged Divisions

Engineering Technology

high GPAs, on average, do well on their projects  student groups with more industry work experience, on average, tend to do better in the project’s soft skills, as well as the ability overall to complete their projects successfully  peer evaluations of group team work provided no data that related to project success  the number of hours worked on the job tended to not have an effect on project successIntroductionThe 2012-13 ABET-ETAC Criterion 5 Curriculum section states that “Baccalaureate degreeprograms must provide a capstone or integrating experience that develops student competenciesin applying both technical and non-technical skills in solving problems.”1. A short search ofASEE Conference papers variously defines the goal

Conference Session

Assessment & TC2K Methods

Collection

2006 Annual Conference & Exposition

Authors

Ahmed Khan, DeVry University-Addison; Robert Lawrence, DeVry University

Tagged Divisions

Engineering Technology

Deans / sequence committees review at course data and take sequence level corrective actionConclusionThe paper presented an overview of the use of Rubrics in the assessment of course and programsobjectives. Rubrics are easy to use and allow faculty to directly assess student knowledge-base,skill levels and competencies in senior project course sequence. The faculty and deans find thefeedback useful for improving the CET/EET curriculum and student performance.References 1. Rogers, Gloria (2005). ABET