Conference Session

Make It!

Collection

2016 ASEE Annual Conference & Exposition

Authors

Clark Hochgraf, Rochester Institute of Technology (CAST)

Tagged Topics

Diversity

Tagged Divisions

Manufacturing

Machine Controlled By ArduinoAbstractThis paper presents an Arduino-controlled Spirographtm-style drawing machine suitable for useat a Maker event. Visitors can use the machine to make unique artwork to take home.Instructions to build the drawing machine are provided. Potential pedagogical uses of thedrawing machine range from learning hands-on construction techniques, to programming,trigonometry, and interaction with a user through sensors.OverviewThis paper provides instructions on how to build a pantograph drawing machine using anArduino UNO microcontroller, a reflectance sensor, two rc-servo motors, and a sheet of foamcore poster board. It is based on the work of Erik Brunvand, Ginger Alford, and Paul Stout [1,2]and extended by using a

Conference Session

Innovations in Curriculum and Course Development

Collection

2016 ASEE Annual Conference & Exposition

Authors

Arif Sirinterlikci, Robert Morris University

Tagged Topics

Diversity

Tagged Divisions

Manufacturing

100 students who have done at least one form of engineering internship. Engineering - Internship-Supervisor Evaluation For each of the following performance characteristics please place an “x” in the line that best reflects your experience with this student. Thank you so very much!Attitude/Application to Learning4 Outstanding and extremely enthusiastic3 Interested and industrious2 Average1 IndifferentAbility to Learn4 Learns very quickly3 Above average in learning2 Average1 Slow to learnDependability4 Completely dependable x3 Above average in dependability2 Usually dependable1 Below average in dependabilityWriting Ability4 Consistently clear

Conference Session

Additive Manufacturing Education

Collection

2016 ASEE Annual Conference & Exposition

Authors

Tzu-Liang Bill Tseng, University of Texas - El Paso; Aditya Akundi, University of Texas - El Paso; Richard Chiou, Drexel University

Tagged Topics

Diversity

Tagged Divisions

Manufacturing

. Puentudura1 is aimed at guiding the process oftechnology integration in a classroom with an ultimate goal of redefining teaching and learningmethodologies. Figure 1 illustrates on how the course curriculum developed for AdditiveManufacturing course at XXXXXX reflects upon SAMR framework.As shown, integrating mobile based scanning technology to additive manufacturing for realizingstudent project designs with the help of SAMR framework helped in significantly enhancing andtransforming the course outlook over the semester. The course enhancement helped in exposing thestudents to effectively integrate mobile based scanning technology, a reverse engineering approachfor identifying and addressing interface challenges. Figure 1

Conference Session

Practical Teaching in Manufacturing

Collection

2016 ASEE Annual Conference & Exposition

Authors

Aaron Lalley P.E., South Dakota School of Mines and Technology; Michael Langerman, South Dakota School of Mines and Technology; Shaobo Huang, South Dakota School of Mines and Technology; Ryan H. Koontz, South Dakota School of Mines and Technology; Lisa Carlson, South Dakota School of Mines and Technology; Eric Jon Holmgren

Tagged Topics

Diversity

Tagged Divisions

Manufacturing

Traditional path t102 Sig. Mean Mean (2-tailed) (SD) (SD)Engr. Self-Efficacy 0-6 4.43 5.00 3.16 .002Design confidence 0-100 56.38 72.69 2.19 .044Expect. of success 0-100 60.03 75.30 2.12 .049 Table 1: students’ differences reflected in pre-surveyThe post-survey was conducted at the end of the semester. Datasets from 49 students wereinvolved in the pre- and post-surveys analyses and 89.4% of them were males. There were nosignificant differences between the students who finished the post-survey and

Conference Session

Innovations in Curriculum and Course Development

Collection

2016 ASEE Annual Conference & Exposition

Authors

Mauricio Torres, Northern Kentucky University; Morteza Sadat-Hossieny, Northern Kentucky University

Tagged Topics

Diversity

Tagged Divisions

Manufacturing

. Table 5. Recruitment and Dissemination InitiativesProposed Curriculum StructureCurriculum at NKU and CSTCC follow the general guidelines for accreditation defined by theAccreditation Board for Engineering and Technology (ABET) [19]. Mechatronics curriculumdesign includes development of goals and objectives, programs of study and curriculum guides,courses, laboratories, textbooks, instructional materials, experiments, instructional sequencies andothe supplemental materials focusing to accomplish a wide range of educational goals [1].The cross-curricular approach reflected at the level of the targeted goals, of the targeted contents,the use of new technologies, of the computer as a working tool which will determine the student’seducational course

Conference Session

Green and Sustainable Manufacturing Education

Collection

2016 ASEE Annual Conference & Exposition

Authors

Tzu-Liang Bill Tseng, University of Texas, El Paso; Aditya Akundi, University of Texas, El Paso; Richard Chiou, Drexel University; Arturo Olivarez Jr., University of Texas, El Paso; Eric D. Smith, University of Texas, El Paso

Tagged Topics

Diversity

Tagged Divisions

Manufacturing