Collection

2005 GSW

Authors

Suketu Shah; Mohammed E. Haque; Gaurav Agarwal

MethodologyThe main thrust of the research was the development of a 3D computer generated animationmodel showing and describing in detail the various elements of an energy conscious architecturaldesign. The following steps outlines the methods used to achieve the above stated purpose.Figure 1 shows the work flow diagram1. Design and Development: The first step was to design and develop a typical single-familythree-bedroom house. Energy consciousness was the prime-governing factor for the design anddevelopment of the house. . Roofing Products Motion Sensors Wall Insulations Daylighting Solar Water Heating Passive Solar

Collection

2014 ASEE Zone 4 Conference

Authors

Selyna Perez Beverly

‘learn by doing’ philosophy. Students in the Cal Poly Pomonaengineering program receive both technical and practical skills to prepare them for the engineeringworkforce. Small class sizes and the integration of a multitude of labs in the engineering curriculumprovide for a robust experience for the student in preparation for a career as an engineer. The student-centered philosophy of the institution supports student involvement and programmatic efforts thatincrease student success and learning. The College of Engineering is the largest college at Cal PolyPomona serving approximately 5,000 undergraduate and graduate students. The student populationconsists of a large number of first-generation, low-income, and underrepresented racial minorities

Collection

2008 GSW

Authors

Kenneth W. Van Treuren; Ian A. Gravagne

Session 16-1 Raising Community Energy Awareness: Building an Energy Display at the Mayborn Museum Kenneth W. Van Treuren Department of Mechanical Engineering Baylor University Ian A. Gravagne Department of Electrical and Computer Engineering Baylor University AbstractEnergy is becoming an increasingly important topic in our lives. Watching the price of energyskyrocket, in particular

Collection

2022 ASEE Midwest Section Conference

Authors

Heather L. Walker; W. Kent McAllister; Michael W. Mourot; J. Robert Dean; Greg Nesmith; Edgar C. Clausen

through Zoom. All 36 mentors attended, with50% in-person and 50% virtual. Of the 55 students participating in the program at that time(some added or dropped later), 48 attended in person, one attended virtually and six did notattend. Figure 1 shows a photograph of a group meeting of the mentors and students at the Kick-off, which was held in the College of Engineering Honors Lounge to support a more formal,professional atmosphere. Figure 1. Mentors and Students in a Group Meeting at the Fall Kick-offThe Kick-off was an opportunity for the mentors and students to get to know each other, do someinitial mentoring and plan the focus and meeting times for activities for the balance of thesemester. The Kick-off included a breakout session

Collection

2008 GSW

Authors

Victor Gallardo; Mequanint Moges; Enrique Barbieri; Aymara Boggiano; Carlos Ramirez

generic modules, and its integration withthe university initiative to train instructional assistants led by the office of Educational Technologyand University Outreach (ETUO). Each module contains an introduction, a detailed presentation ofcontents and assessment sections that can easily be adopted by other departments and collegesacross the university. The assessment of the effectiveness of these modules is conducted bysurveying the coordinating faculty, the trainees (the new instructors), and the university studentswho ultimately receive the instruction from the trainees.The results indicate that the new hybrid orientation programs helped increase the performance of ourteaching assistants: they recognize the usefulness of the training sessions

Collection

2015 Spring ASEE Middle Atlantic Section Conference

Authors

Nisha Kondrath; Mark A. Jupina

Department of Electrical and Computer Engineering at Villanova University. This flipped-lab approach would (1) provide opportunities for faculty to challenge the students to perform more complex electronic circuit designs and (2) foster more productive and student-centered peer-to-peer interactions. This paper discusses the implementation of the pedagogy with examples of specific projects, faculty experiences and challenges, and student feedback with the new approach.I. Introduction Benjamin Franklin once said, “Tell me and I forget. Teach me and I remember. Involve me and I learn.” In addition to the proficiency in the technical knowledge, it is important for the students to also become erudite self-learners and effective team players. To

Collection

2008 Pacific Southwest Section Meeting

Authors

Constantin Ciocanel; Mohammad Elahinia

testing, such as strain gages, load frames, impact hammers, and spectrum analyzers;(2) reinforced material studied in previous mechanics and vibrations courses; (3) improved dataanalysis skills, and (4) further developed laboratory and technical writing skills.”Prior to this redevelopment, as part of the subject-based approach, a classroom lecture precededeach laboratory session. The lecture consisted of the review of the theory pertaining to eachexperiment to help students refresh their knowledge on the subject. Additionally the descriptionand procedure of the laboratory experiment was covered during this lecture. Prior to each class,the lecture notes, along with the laboratory procedures, were posted on the course website. Thestep-by-step

Collection

2007 ASEE Midwest Section Conference

Authors

William A. Kline; Thomas Mason

32. Structure and Evolution of RHV ProgramThe current mission of the RHV program is to engage technology based businesses to provideoutstanding educational opportunities for students. Using the earlier successes with start-upcompanies, the program is now promoted to technology based companies of all sizes, maturities,and types to identify technical needs they may have and to create structured project work that canbe executed in the RHV program as shown in Figure 1. A legal agreement is executed includinga general project scope and terms concerning confidentiality, intellectual property, andindemnity. The companies contribute the technical needs and financial support to thearrangement. The RHV program provides dedicated infrastructure

Collection

2004 GSW

Authors

H. R. Myler

anduniversities titled Closing the Gaps by 2015 (adopted in October 2000 by the Texas HigherEducation Coordinating Board)1. The plan, which is directed at closing educational gaps withinTexas, as well as between Texas and other states, has four goals: to close the gaps in studentparticipation, student success, excellence, and research. The plan includes strategies for reachingeach of the goals and an annual performance measuring system. One outcome of this plan was ademonstrated need for engineering education and an outcome of this was the creation of the non-profit membership organization known as the Texas Engineering and Technical Consortium(TETC). The purpose of TETC is to increase the number of engineering and computer sciencegraduates from Texas

Collection

2002 ASEE North Midwest Section Conference

Authors

James N. Almquist; D. Joanne Wilson

Changes in Freshman Engineering Students Bring Changes to Introductory Engineering Courses James N. Almquist D. Joanne Wilson General Engineering Department UW-PlattevilleAbstract: All freshmen interested in engineering at UW-Platteville take both of our twocredit courses: Introduction to Engineering and Engineering Computer Graphics. In thispaper, we discuss the changes we have made to these courses in response to the changeswe are seeing with respect to the incoming students. The two biggest changes are thatmany students are starting their academic careers at lower math levels

Collection

2013 Pacific Southwest Section Meeting

Authors

Tammy Yut-Ling Chan; Gustavo Borel Menezes

improve their work throughout thequarter.Key features of the courses included: 1) Dedicated class time was dedicated for students andinstructors to work together; 2) Teamwork enabled students, under time pressure, to analyzeengineering problems, formulate solutions, program, write, and prepare presentations; 3)Engineering problems were solved with widely-available software; and 4) Teams competed toproduce the best course manual for next year’s course.Preliminary results from surveys showed that students felt more confident and knowledgeablewhen presenting technical information, writing their reports, and using computer tools in theirsubsequent courses. They also used these skills later in their senior design projects. Compared totheir peers who

Collection

2009 GSW

Authors

Kendrick Aung; Ryan Underdown P.E.

recognizetheir learning style. Campers participated in interactive demonstrations to gain insight to howstudents learn. Researchers at PSU discussed their innovative research in engineering. Campersasked probing questions and generated a stimulating discussion on a wide variety of topicsincluding nano-technology and how science integrates with engineering. Some detaileddiscussions of topics used in the camp were described below.Bicycle of Yesterday and Today LabIn this lab session, the main purpose is to provide some engineering knowledge and hands-onactivities related to design and analysis of a bicycle. The students were already exposed totopics such as simple machines, and the lab provided further knowledge relating simplemachines to different parts

Collection

2023 ASEE Midwest Section Conference

Authors

Oghenetega A. Obewhere; Karen A. Cerda; Rajesh Keloth; Shudipto K. Dishari

. Organize virtual team-building activities to foster a sense of community and collaboration: Virtual team-building activities are an excellent way to foster a sense of community and collaboration among participants in a virtual camp. It also promotes an inclusive environment for all participants. We started each camp session with icebreaker questions which allowed the students to share a little bit about themselves and/or their experiences. We realized that this helped ease them into the business of the day and encouraged their full participation. 6. Offer technical support to address issues that may arise. 7. Establish a feedback system to gather inputs from participants: We prepared anonymous

Collection

2008 GSW

Authors

August Allo; Carol Costello

Session 13-1 Targeted Recruitment of Disadvantaged Students:The Multiplier Effect of Senior Electrical Engineering Design Demonstrations August Allo, Carol Costello Department of Electrical and Computer Engineering University of Texas at San Antonio AbstractAlthough the importance of Electrical and Computer Engineering is recognized as one of thecritical areas for producing technically competitive graduates, recruitment of students to this areapresents a challenge. In part, this is due to the fact that Electrical and

Collection

2007 St.Lawrence Section Meeting

Authors

Jason Salonga

affinity than most would think, an affinity rooted in design. I the medium; let us refer to this as pre-production. Students would then proceed to research, de-claim that good engineering designers, like good visual artists, have the ability to generate and sign, and produce their artwork; let us refer to this as production. Upon completion, all projectsdevelop ideas, have strong technical skills, and are aware of the significant works in their field. would be exhibited and then critiqued by the class and professor; let us refer to this as post-Although their tools, techniques, objectives, and constraints may differ, their underlying proc- production. These three stages would cycle with each studio project

Collection

2007 North Midwest Section Meeting

Authors

Michael P. Hennessey

as atype of modern system dynamics, in which CAD and animation are brought in for significantvisualization to enhance understanding of mechanical systems that incorporate motion as well asto appeal to a wide audience, some of whom may not be technically oriented. This paperdescribes such a course and its advantages. Sample student project work is shown thatemphasizes applied mathematical modeling, CAD modeling, modeling and simulation usingMATLAB® and Simulink®, and animation of specific scenarios of interest using SolidWorks®with the Animator add-on. Projects show-cased include: (1) the zero-friction skiingbrachistochrone problem, (2) the kinematic car with both front and rear wheel steering, (3) theN-pendulum chain approximation of a

Collection

2011 Fall ASEE Middle Atlantic Section Conference

Authors

Radian Belu

connectedrenewable or hybrid energy systems. During the second part of the quarter the students arerequired to design, via a project a hybrid power systems, integrating wind, PV and energystorage systems to provide power for a specific load. The project is handled by a team of 3 to 4students. The project is part of the final grade of the students, and is complementary to the finalexam. The students are free to make the team based on their preferences and mutual interests.They are required to make a 10-min presentation on the project topic during the final exam weekof the quarter. The outline of the course includes (ten 3-hour lectures/units): 1. Basic principles of energy generation 2. Introduction to renewable energy systems 3. Electric machines

Collection

2010 North Midwest Section

Authors

Thomas F. Quinn; Ronald H. Brown; George F. Corliss

reality that the bestengineering decisions are not always the best business decisions, and vice-versa. Issues of cost,scalability, competitiveness, and others often force compromises into what might otherwise bethe most elegant engineered solutions possible. An engineer new to the workplace might feel abit disillusioned seeing how solutions are designed to meet multiple, often non-technical,objectives.There’s also the thorny matter of customers with their own wants and needs, their own businessobjectives, and their own varying levels of competency and available technical support – messyissues that don’t often intrude into an engineer’s education. Delivering and supportingengineered products into customers’ hands to generate value for their

Collection

2008 ASEE Zone 1 Conference

Authors

NADIYE O. ERDIL; KOENRAAD E. GIESKES

same material as was being asked in the traditional sections, were completely dedicated tosolid models and drawings of a water mill. In the first class, the students were split up into five teams offour people. Each group was assigned a particular component of a water mill, e.g., the support, the wheel,the bucket, etc., and asked to generate a solid model of these components with dimensions that wereprovided. The second week, all groups were asked to create technical drawings of their assignedcomponents. During the week following the trip, the students were asked to combine all the separate partsof the mill into an assembly of the water mill.The trip to the Wagner Mill took place on a Saturday morning and consisted of students

Collection

2004 ASEE Midwest Section Conference

Authors

Cathryne Stein

Botball are threefold: 1. to create more technically literate students and teachers; 2. to encourage more students to go into science, engineering, math, and related fields; 3. to use robotics to engage students in engineering, science, and math, and help them understand how and why they can use the tools of math and science to do important and creative work.Botball uses the activities of robot programming, design, and construction as well aswebsite development to get students excited about being on the creative side oftechnology.Our strategy in pursuing these goals involves providing both a short and long termapproach towards improving the effectiveness of schools in teaching science, math, andtechnology. Specifically, we

Collection

2014 Fall ASEE Middle Atlantic Section Conference

Authors

Lethia Jackson; Courtney Lamar; Quincy Brown; Velma Latson

) TABLE II Monday Online safety Introductions LEGO Learn Phase Outline HTML 5 HTML 5 Robots Day Topic/Technology Online 1 General Online Safety Guidelines Hosting Developing Basic Web Pages (HTML5) Tuesday JavaScript 3D Printing LEGO 2 JavaScript Makey Online Robots MakeyMakey Makey safety Arduino 3 Raspberry Pi LilyPad Python

Collection

2025 Northeast Section Conference

Authors

Jun Zhang; Peter Cavanaugh; Dan Tenney

educational andFramework) to mitigate technological risks introduced by AI technological implementation. It involves changing mindsets,and other services. adopting new learning platforms, ensuring transparency in AI Pedagogical and educational practices: it is important for systems, building relevant competencies, and implementingboth student and faculty that not only leverage AI tools for supportive policies. Together, these steps can lead to moreimproving learning experience but also cultivate the ability to adaptive, reliable, and non-intrusive teaching and learningcritically evaluate AI-generated content while maintaining experiences. Table 1 is a list of

Collection

2011 Fall ASEE Middle Atlantic Section Conference

Authors

Paul G. Ranky

industrial engineering,engineering quality management, project management, concurrent / simultaneous greenproduct / process design, visual lean factory management, and continuous professionaleducation. 557IntroductionMillennial generation students are interested in an integrated, simultaneously analytical,computational, interactive, as well as practical, real-world-focused, customized education.They expect a large number of choices, because they understand the power of simulation.They are very visually focused, because this is the video gaming generation. They wantpersonalized, customized products, processes and service, and their education process isnot an exception. They look for technical details, and want

Collection

2011 Pacific Southwest Section Meeting

Authors

Angela Beck; Jim Helbling

quality of the various design projects improvedbut also the frequency and severity of interpersonal conflicts has been minimized.The fourth and final activity is an open work session. During this activity students are free towork on their tasks, whether analyzing, manufacturing, testing, or documenting; both instructorsare available throughout the work session to help with either technical or communication tasks.If team members are having trouble working together, then this time is also used to meetprivately with the students in question in order to mediate these conflicts. This addition ofconflict mediation is one of the key improvements to this team-teaching configuration as will bediscussed in the following section.Key Alterations and

Collection

2008 GSW

Authors

Cheryl L. Willis

Session 11-1 Using the Labor Market Information System to Inform Continuous Program Improvement Efforts Cheryl L. Willis Information and Logistics Technology Department University of Houston AbstractThe federal government has recognized the need to coordinate efforts of key government agencies; educationalproviders; and private business to build a common approach to workforce and economic development. Thisapproach to build a

Collection

2008 GSW

Authors

Mohan A. Ketkar; Nripendra N. Sarker

, techniques,skills and modern tools of their disciplines”.Three performance criteria listed below were developed for this outcome group. 1. Students are able to solve problems using current software used in the discipline (such as Matlab, Autocad, Multisim, Pspice, .NET, C++ compiler, etc) 2. Students are able to utilize the latest available hardware/equipment used in the discipline (such as signal generators, oscilloscope, computer hardware) 3. Students are able to utilize latest problem solving and design techniques and methods in their discipline (such as numerical techniques and the design process)Performance Criteria ‘b’TAC Criterion 2, Outcome ‘b’ states, “an ability to apply current knowledge

Collection

2013 GSW

Authors

Amit Oza; Gary Coleman; Lex Gonzalez; Bernd Chudoba; Paul Czsyz

Saturday Morning Session 1 - Student Solution Space Screening of a Hypersonic Endurance Demonstrator Amit Oza, Gary Coleman, Lex Gonzalez, Bernd Chudoba Mechanical and Aerospace Engineering Department University of Texas at Arlington Paul Czysz Hypertech Concepts LLC St. Louis, MO AbstractThe Solution Space Screening for a Hypersonic Endurance Demonstrator program was atwo and one-half month study to: Demonstrate the Aerospace Vehicle Design (AVD) Laboratory

Collection

2021 ASEE Midwest Section Conference

Authors

Mostafa Elsaadany; Timothy J. Muldoon; Raj R. Rao

Engineering courses based on instructors’ experiences andpost-hoc reviews of students’ evaluations. Several students reported a lack of quality internetconnection to follow course announcements, watch the video lectures, interact with theirclassmates or course instructor, and work on assignments. Other students exhibited a lack ofdigital literacy despite having access to both quality internet access and computers. Digitalliteracy widely misidentified and often referred to as device literacy- is the ability to obtain,assess, and generate information using information and communication technologies [1]. Beingdigitally literate requires the possession of both cognitive and technical skills. Based on thisdefinition, we observed many students who

Collection

2018 ASEE Conferences - Conference for Industry and Education Collaboration / San Antonio proceedings

Authors

Claudio Brito; Melany Ciampi

– Proceedings of the 2018 Conference for Industry and Education Collaboration Copyright ©2018 American Society for Engineering Education Session ETD 526International Institute of Education is a bold and resilient source of innovation in highereducation [1].EDUCATIONAL ASPECTS OF CONTEMPORARY HIGH EDUCATIONNo doubt that work environment has been changing drastically and it takes place worldwide andtoday millions of professionals are also unemployed, even in advanced economies. On the otherhand, businesses in advanced economy countries claim that they often are not able to findworkers with the required skills. It is a fact that this is a

Collection

2013 Pacific Southwest Section Meeting

Authors

Liang Li Wu; Anis Hammoudeh; Gregory Washington

and the increase in the number of cell-phone users went from two per 1,000people in 1990 to over 500 per 1,000 people today. Furthermore, due the globalized market,engineering industries, which cannot compete globally, are not likely to survive domestically1.To be successful internationally, one is required to have cultural and economic expertise as wellas solid technological background. Thus, the engineering education encounters shiftingparadigm of how to train our next generation to be global leaders in the field, not onlyengineering ready, also culturally ready.While the Henry Samueli School of Engineering was initiating future international programs toeducate our students on a dynamic pathway, an incident occurred on campus has altered