Asee peer logo

New Method for Testing Induction Machines in a Teaching Laboratory

Download Paper |

Conference

2023 ASEE Annual Conference & Exposition

Location

Baltimore , Maryland

Publication Date

June 25, 2023

Start Date

June 25, 2023

End Date

June 28, 2023

Conference Session

Energy Conversion, Conservation and Nuclear Engineering Division (ECCNE) Technical Session 4

Tagged Divisions

Energy Conversion and Conservation and Nuclear Engineering Division (ECCNE)

Page Count

10

DOI

10.18260/1-2--44002

Permanent URL

https://peer.asee.org/44002

Download Count

126

Request a correction

Paper Authors

biography

Herbert L. Hess University of Idaho

visit author page

Herb Hess is Professor of Electrical Engineering at the University of Idaho. He received the PhD Degree from the University of Wisconsin-Madison in 1993. He is a Fellow of the ASEE. His research and teaching interests are in power electronics, electric machines and drives, and electric power quality. He writes this paper during his fortieth year of teaching electric machines.

visit author page

author page

Emily M. Conroe

author page

Daniel Taylor

Download Paper |

Abstract

This paper presents a new testing method for an induction machine’s torque-speed curve. The incumbent testing method for determining an induction machine’s torque-speed curve uses a DC generator coupled to the shaft of the induction machine,[1] delivering the energy to an external resistive load bank. Consistent and precise steady state characterization is readily obtained from this setup and then used to verify an appropriate model. This proposed new method uses a squirrel cage induction machine driven by either variable speed regenerative drive or a synchronous machine, replacing the coupled DC machine and load bank. This opens an insightful new way to operate induction machines in a teaching laboratory.

In this new configuration, the test machine is electrically connected at its specified frequency, typically 50 Hz or 60 Hz. The variable speed drive runs the load machine over a range of frequencies between the difference and sum of the specified frequency and the test machine’s rated slip. Within these limits, the torque-speed curves of the test machine and the load machine intersect safely at a two unique points of operating torque and speed for each frequency applied to the load machine. One of these points is always stable and within the test machine’s normal operating range. Torque may be measured by a transducer or calculated using data from a model of the load machine. In addition to torque and speed, other important operating information and test data about the test machine can be measured, such as current, power factor, and energy efficiency. For better noise performance, a synchronous machine may be used to supply the load machine at variable frequency.

The context for this new test method is a twin simulation of a wind turbine generator. The test machine is a Type III generator. The load machine is configured to mimic the wind turbine that is directly coupled to the generator. Together, they provide a hardware test platform for a wind turbine generator. The software twin of this system is a complete digital simulation of it. Ideas can be tried and improved in software before verifying them on the hardware. Of course, a good software model is a must for such a test bed concept, hence this paper on how to obtain important performance information without the expense of decoupling and modifying the test bed.

The paper will describe how the test bed performed with students in the lab for both teaching and research. This will be supported by students’ simulation and experimental results.

[1] “IEEE Standard Test Procedure for Polyphase Induction Motors and Generators,”IEEE Standard 112, 1991.

Hess, H. L., & Conroe, E. M., & Taylor, D. (2023, June), New Method for Testing Induction Machines in a Teaching Laboratory Paper presented at 2023 ASEE Annual Conference & Exposition, Baltimore , Maryland. 10.18260/1-2--44002

ASEE holds the copyright on this document. It may be read by the public free of charge. Authors may archive their work on personal websites or in institutional repositories with the following citation: © 2023 American Society for Engineering Education. Other scholars may excerpt or quote from these materials with the same citation. When excerpting or quoting from Conference Proceedings, authors should, in addition to noting the ASEE copyright, list all the original authors and their institutions and name the host city of the conference. - Last updated April 1, 2015