Conference Session

International Collaborations

Collection

2018 ASEE Annual Conference & Exposition

Authors

Gary Bruce Gehrig P.E., University of North Carolina, Charlotte

Tagged Topics

Diversity

Tagged Divisions

International

inequality in the world (African Development Bank, 2007) with aGini coefficient estimated at 0.58 by the 2009/10 household survey, which is one of the highestfigures of any country in the world (World Bank, 2009). The country has an estimated annualGDP per capita of USD 5293. However, it is worth noting that from 1980-1990 Namibia had aGDP per capita which was higher than that of both China and Thailand. But, over the interveningtime both countries’ rate of economic growth have greatly exceeded Namibia’s and, as a result,Namibia’s GDP per capita ratio is currently much smaller than either of those two countries(National Planning Commission, 2012).Despite this disparity in economic growth rates, the country is slowly emerging from thecompounding

Conference Session

Building and Engaging Communities for Scholarship, Advocacy, and Action for Diversity, Equity, and Inclusion

Collection

2018 ASEE Annual Conference & Exposition

Authors

Rebecca A. Bates, Minnesota State University, Mankato; Eric Specking, University of Arkansas; Adrienne Minerick, Michigan Technological University; Stephanie Farrell, Rowan University; Rocio C. Chavela Guerra, American Society for Engineering Education

Tagged Topics

ASEE Diversity Committee, Diversity

Tagged Divisions

International, Minorities in Engineering

PlanThe activities of the ASEE Diveristy Committee have been guided by a communal vision andhave informed and been informed by (a) the task force charge in 2009, (b) initial plans developedby the committee in 2011-12, (c) and a formal strategic action plan developed in 2015-16. TheASEE statement on diversity and inclusion describes the Society’s vision as to create and foster environments where every individual is respected and no one feels marginalized. ASEE believes that this can be achieved by supporting the education, recruitment, retention, and advancement of these groups in engineering education, engineering technology education, and the engineering profession. While ASEE recognizes that steady gains have been

Conference Session

Humanitarian and Sustainability in a Global Engineering Context

Collection

2018 ASEE Annual Conference & Exposition

Authors

Renetta G. Tull, University of Maryland, Baltimore County; Shawnisha Hester, University of Maryland, Baltimore County; Yarazeth Medina, University of Maryland, Baltimore County; Denise Nicole Williams, University of Maryland, Baltimore County; Hector E. Medina, University of Maryland, Baltimore County; Erika T. Aparaka, University of Maryland College Park

Tagged Topics

Diversity

Tagged Divisions

International

among Underrepresented Scholars through Engagement with the Sustainable Development Goals in Global ContextsIntroductionOpportunities to participate in international engagement experiences broaden students’perspectives and perceptions of real world problems [1]. A strong sense of “global engineeringidentity” can emerge when students are part of international teams that consider solutions tohumanitarian challenges [2], [3]. To encourage retention in engineering among undergraduateand graduate students from underrepresented groups, a multi-campus team of faculty andadministrators developed a plan to expose students to humanitarian engineering perspectiveswithin global contexts. Through the University System

Conference Session

Humanitarian and Sustainability in a Global Engineering Context

Collection

2018 ASEE Annual Conference & Exposition

Authors

Michael F MacCarthy, Mercer University; Holly F. Berns, Mercer University ; Ryan Monty, United Nations Humanitarian Response Depot; Mitzi Erin Brett; Zachary Lewis Martin; Pietro Sannipoli, United Nations Humanitarian Response Depot; Nicolas Jerome Messmer; Walid Ibrahim; Scott Schultz, Mercer University; Katelyn C.N. Dimopoulos, Mercer University

Tagged Divisions

International

solutions for small-scale gold miningcommunities), Vietnam (low-cost prosthetics), South Korea (technical training of North Koreanrefugees), Kenya (drinking water), and Madagascar (drinking water and sanitation).As part of their partnership agreement, MUSE and WFP have collaborated through UNHRDLAB in: designing and developing relief items and logistics solutions for the supply chain,focusing on cost-effective green technologies and on reducing packaging waste (thus enhancingefforts in emergency preparedness planning and response operations); and sharing knowledgeand building capacities.The Mercer Partnership with UNHRDThe unique partnership between MUSE and UNHRD has grown since late-2014, as describedbelow by academic calendar year.2014-2015. The

Conference Session

International Engineering Education Poster Session

Collection

2018 ASEE Annual Conference & Exposition

Authors

Miguel Rafael Ruiz-Carpio; Cyrus Safai, Salt Lake Community College; Arafat Djobo; Ivan Gaichuk; Nick M. Safai, Salt Lake Community College

Tagged Topics

Diversity

Tagged Divisions

International

Paper ID #21943Industry experience: Consulting; since 1987; Had major or partial role in: I) performing research forindustry, DOE and NSF, and II) in several oil industry or government (DOE, DOD, and NSF) proposals.Performed various consulting tasks from USA for several oil companies (Jawaby Oil Service Co., WAHAOil and Oasis Co., London, England). The responsibilities included production planning, forecastingand reservoir maintenance. This production planning and forecasting consisted of history matching andprediction based on selected drilling. The reservoir maintenance included: water/gas injection and gas liftfor selected wells to optimize reservoir production plateau and prolonging well’s economic life.Terra Tek, Inc., Salt Lake City, UT

Conference Session

Humanitarian and Sustainability in a Global Engineering Context

Collection

2018 ASEE Annual Conference & Exposition

Authors

Rodolfo Valdes-Vasquez, Colorado State University; Caroline Murrie Clevenger P.E.; Laura Thornes; Svetlana Olbina

Tagged Divisions

International

formed a partnership to host a 12-day travel study program. CSU had originallyoffered the program in the Caribbean in 2009; the following year it was offered in partnershipwith the University of Costa Rica. Most recently, the latest iteration of the course is based on anew partnership with EARTH University. This paper provides context about the organizationalchallenges and lessons learned from this partnership. First, this paper describes a brief overviewof the study abroad program including the content, structure, and assignments. Second, the paperprovides a discussion of the challenges related to planning and executing this course. Finally,lessons learned by the faculty leaders and support staff provide insights about what to expectwhen

Conference Session

Why Can't We Get Faculty and Students to Go Abroad?

Collection

2018 ASEE Annual Conference & Exposition

Authors

David B. Knight, Virginia Tech; Holly M. Matusovich, Virginia Tech; Mayra S. Artiles , Virginia Tech; Kirsten A. Davis, Virginia Tech; Timothy Kinoshita, Virginia Tech; Diana Bairaktarova, Virginia Tech; Kacie Hodges P.E., Virginia Tech; Tamara Knott, Virginia Tech; Walter C. Lee, Virginia Tech; Marlena McGlothlin Lester, Virginia Tech ; Lisa D. McNair, Virginia Tech; Kenneth Reid, Virginia Tech; Denise Rutledge Simmons P.E., Virginia Tech

Tagged Divisions

International

McGlothlin Lester, Virginia Tech Marlena McGlothlin Lester is the Director of Advising for the Department of Engineering Education at Virginia Tech. She leads the undergraduate advising team and oversees the advising process for all General Engineering students. She is responsible for the development of a hands-on, minds-on orien- tation model for all first-year engineering students, the creation of a comprehensive engineering major exploration tool, Explore Engineering, and enhancement of the academic planning resources available for first-year engineering students. Marlena strives to transform the advising experience for students and advisors through communication, collaboration, and consistency.Dr. Lisa D. McNair

Conference Session

International Collaborations

Collection

2018 ASEE Annual Conference & Exposition

Authors

Steven J. Burian, University of Utah; Mercedes Ward, University of Utah; Sajjad Ahmad, University of Nevada, Las Vegas; David Lawrence Stevenson; Tariq Banuri, University of Utah; Muhammad Aslam Chaudhry, University of Utah; Rasool Bux Mahar P.E., Mehran University, Jamshoro; Jeffrey D. Ullman, Stanford University

Tagged Topics

Diversity

Tagged Divisions

International

awarded the Glen L. Martin ASEE Civil Engineering Division Best Paper Award. Steve is a registered professional engineer in Utah.Dr. Mercedes Ward, University of UtahProf. Sajjad Ahmad, University of Nevada, Las Vegas Dr. Ahmad is a Professor in the Department of Civil and Environmental Engineering and Construction at the University of Nevada, Las Vegas (UNLV). His teaching and research interests are in the area of sus- tainable planning and management of water resources, water-energy nexus, and stormwater management . He is particularly interested in using systems approach to address water sustainability issues.David Lawrence StevensonProf. Tariq Banuri, University of Utah Professor Tariq Banuri, Department of

Conference Session

Study and Research Abroad

Collection

2018 ASEE Annual Conference & Exposition

Authors

Charles McIntyre, Indiana University-Purdue University of Indianapolis; Ryan A. Camp, Indiana University-Purdue University of Indianapolis; Patricia Fox, Indiana University-Purdue University of Indianapolis; Shawn Patrick

Tagged Topics

Diversity

Tagged Divisions

International

Francis delivered an encyclical on the environment and humanecology. “Laudato de si” [10] which calls upon all peoples of the world, especially those of theChristian faith, to recognize the Earth as sacred and to direct daily actions accordingly. Byfocusing attention on what can be done at the individual and local levels, individuals andcommunities become accountable for preserving resources and living in a more sustainablemanner. Joining in this call are a number of other faith leaders.Germany has been addressing sustainable policy and practices in business, industry and withintheir municipalities for decades. The results are impressive when considering sustainable urbanstructures and planning, renewable energy usage, national recycling

Conference Session

International Engineering Education Poster Session

Collection

2018 ASEE Annual Conference & Exposition

Authors

Dong Liang, Sichuan University; Senbao Lin, Sichuan University - Pittsburgh Institute; Lurao Liu, Sichuan University; Wei Chen, Sichuan University - Pittsburgh Institute; Jared Yi Du, Sichuan University

Tagged Divisions

International

hands-on practice. Theorganization, facilities, challenges, and planning of Makerspace are also presented to guideothers in the creation of similar organizations. IntroductionSichuan University-Pittsburgh Institute (SCUPI) is a new academic entity jointly establishedby Sichuan University (SCU) and the University of Pittsburgh (Pitt). This institute is arealization of the new archetype of institute-scale, collaborative entities between leadinguniversities in the U.S. and China. SCUPI is designed to follow an international model and isaimed to provide a world-class engineering education that focuses on design, innovation, anda global vision. Currently, it offers three undergraduate programs in Mechanical

Conference Session

Humanitarian and Sustainability in a Global Engineering Context

Collection

2018 ASEE Annual Conference & Exposition

Authors

Patricia Fox, Indiana University-Purdue University of Indianapolis; Charles McIntyre, Indiana University-Purdue University of Indianapolis; Brandon Sorge, Indiana University-Purdue University of Indianapolis

Tagged Topics

Diversity

Tagged Divisions

International

have been impressive in sustainable urbanstructures and planning, renewable energy usage, sustainable transportation systems, and greenpolicies at the local, state and national levels [6]. All of these sustainable efforts have led toeconomic growth and innovation within Germany [6]. The German’s have instituted laws topromote a more environmentally sustainable country, the product of decades of work totransform their country into a “green” energy, urban and transportation model. Germany hasprospered under this sustainable plan and maintained growth, even after the recession in 2008,emerging with a strong economy [6]. The German government’s current sustainabledevelopment strategy plan is based on a long term holistic, integrated approach with

Conference Session

International Engineering Education Poster Session

Collection

2018 ASEE Annual Conference & Exposition

Authors

Jiaojiao Fu, Beihang University; Deborah M. Grzybowski, Ohio State University; Qing Lei, Beihang University; Dongya Cheng, Tibet University

Tagged Divisions

International

potentiallymake improvements in curriculum based on these findings. Therefore, this paper takes theFirst-year Engineering Honors Program at the Ohio State University in the United States andthe Engineering Experimental Class at Beihang University in China as their case studies ofinternational comparison of the entire first two years’ curriculum. As an intermediary ofteaching activities and the basic guarantee of achieving educational goals, course is ablueprint and plan for cultivating what types of people. This paper takes courses as theresearch object, compares the whole course setting, and studies the syllabi of basic coursesand teaching methods reflected in the syllabi. Methodologies including text analysis,frequency analysis, comparative research

Conference Session

Cooperative and Project-based Global Learning

Collection

2018 ASEE Annual Conference & Exposition

Authors

Anna Friesel, Technical University of Denmark

Tagged Divisions

International

involving participants from different countries and cultures may differ greatlydepending on the educational traditions of the students’ homelands. We describe our internationalactivities with a focus on international students’ projects performed in cooperation with technicaluniversities abroad in order to offer the students the possibility to train their international skills.Developing and planning of such activities often gives some more practical challenges, such asdifferences in how engineering programs are designed, the differences in academic calendars andthe amount of credits given for projects and courses in different countries. In some cases, thedifferences in academic calendars are so big, that it is a major obstacle in arranging

Conference Session

Cooperative and Project-based Global Learning

Collection

2018 ASEE Annual Conference & Exposition

Authors

Karim Altaii, James Madison University; Shannon N. Conley, James Madison University ; Samy El-Tawab, James Madison University

Tagged Topics

Diversity

Tagged Divisions

International

energy monitoringcapabilities, and six back up units in the event of malfunction or damage to a node. All unitswere switchable through an iOS application accessible by the end-user from any place in theworld which is connected to the internet. For security reasons [18, 19], the application can limitaccess to a certain area (using IP addresses) or a specific city, but for testing purposes, the teamdecided to rely on the encryption of the username and password given to users and storedsecurely in the cloud database [20].The team considered differences between the US-energy power and the target AC units’ physicalspecifications. The plan was to start the installation of one unit to ensure the procedure could bereplicated with additional AC units

Collection

2018 ASEE Annual Conference & Exposition

Authors

Waddah Akili, Iowa State University

Tagged Divisions

International

break thetraditional lecture dominant pattern when cooperative learning protocols are deployed. Thepaper will illustrate how cooperative learning can advance academic success, quality ofrelationships, psychological adjustments, and attitudes toward the college experience. Whatneeds to be done to move the process forward? What are the key components of successfuldeployment of active learning in general and cooperative learning in particular? How tofoster and expand the community of engineering faculty who use cooperative learning?What plans, efforts, and resources need to be mobilized to institutionalize pedagogies ofengagement including cooperative learning at the department or college level?Next, it identifies barriers to reformation in

Conference Session

Why Can't We Get Faculty and Students to Go Abroad?

Collection

2018 ASEE Annual Conference & Exposition

Authors

Gregg Morris Warnick, Brigham Young University; Marie S. Call, Brigham Young University; Randall Davies, Brigham Young University

Tagged Topics

Diversity

Tagged Divisions

International

feelthat citing financial restrictions is a more acceptable response [7], Other studies indicate thatfinancial constraints are not so much evidence of an active barrier to participation as a retroactivejustification for the decision not to participate [8]. Most studies believe that the apparentfinancial barrier is more of a misinformation barrier. There is often more financial aid availablethan most students are aware and this combined with the possibility that students tend tooverestimate the cost of study abroad in their minds [7].B. Socio-Economic BackgroundWhile the financial barrier is probably over-cited and blown out of proportion, it is important tonote that lower income students are less likely to plan to study abroad than higher

Conference Session

International Engineering Education Poster Session

Collection

2018 ASEE Annual Conference & Exposition

Authors

Pradeep Kashinath Waychal, Western Michigan University; Jayantrao Bhaurao Patil, R. C. Patel Institute of Technology, Shirpur, India; Pramod Jagan Deore, R. C. Patel Institute of Technology, Shirpur, India; Suhas Pandit Shukla, R. C. Patel Institute of Technology

Tagged Topics

Diversity

Tagged Divisions

International

of studies, and course content. Since performance of students in previous examination decides their ability tounderstand topics in current classes, we requested the teachers to study details of the pastperformances of their students (high school courses and performances, therein, performancesat other competitive examinations) and plan their courses accordingly. They introduced teststo assess students’ understanding of pre-requisite topics and developed course plans includingthe use of appropriate pedagogical methods. For each class, the same teacher was responsiblefor both lectures and tutorials, which facilitated more contact time with the students resultingin better academic integration. The teachers prioritized learning (as

Conference Session

International Engineering Education Poster Session

Collection

2018 ASEE Annual Conference & Exposition

Authors

Junyi Ying, Shanghai Guanghua College (High School); Cyrus Safai, Salt Lake Community College; Junior Onyeagba, University of Utah; Nick M. Safai, Salt Lake Community College; David Richardson, Salt Lake Community College; Peter Joseph Iles, Salt Lake Community College; Rajan P. Kochambilli, Salt Lake Community College

Tagged Topics

Diversity

Tagged Divisions

International

, Electrical, Environmental, Mechanical, Manu-facturing, Bioengineering, Material Science), and as Faculty in the engineering department for the pasttwenty seven years.Industry experience: Consulting; since 1987; Had major or partial role in: I) performing research forindustry, DOE and NSF, and II) in several oil industry or government (DOE, DOD, and NSF) proposals.Performed various consulting tasks from USA for several oil companies (Jawaby Oil Service Co., WAHAOil and Oasis Co., London, England). The responsibilities included production planning, forecastingand reservoir maintenance. This production planning and forecasting consisted of history matching andprediction based on selected drilling. The reservoir maintenance included: water/gas injection

Conference Session

Global and Intercultural Competency

Collection

2018 ASEE Annual Conference & Exposition

Authors

Scott Daniel, Swinburne University of Technology; Nick John Brown, Engineers Without Borders Australia

Tagged Divisions

International

. Since the recording of program genderdata began in mid-2016, 45% of program participants have identified as female. In order tomaximise student participation and minimise disruption to university schedules each Summitis scheduled to run between semesters (Dec-Feb and Jun-Jul). Approximately half of studentshave their participation funded by Australian Government New Colombo Plan mobilitygrants. This grant requires the Summit form a formal part of a student’s university course,whilst most students use the experience as part of required work experience the HumanitarianDesign Summit Program has been integrated into formal curriculum such as research thesisprojects and as part of the ‘Engineering in a Humanitarian Context’ course at the

Conference Session

Study and Research Abroad

Collection

2018 ASEE Annual Conference & Exposition

Authors

Homero Murzi, Virginia Tech

Tagged Divisions

International

(thus projects had to be very well thought). In contrast, students were notrequired to achieve or deliver anything, it was their own initiative. A successful project was not one thatdelivered outcomes but one that delivered engagement. Although this study is exploratory and we are not measuring any outcome as part of it, we plan toconduct further research in the future to identify and measure the learning and professional outcomes of theIcarus program. Figure 1. Floyd-Smith, Wilson [14] model of outcomes of students’ engagement One impact of extracurricular activities on undergraduate students, there is research supporting thenotion that out-of-the classroom learning experiences promote students’ engagement with

Conference Session

Humanitarian and Sustainability in a Global Engineering Context

Collection

2018 ASEE Annual Conference & Exposition

Authors

Christina Kay White, Massachusetts Institute of Technology; Renetta G. Tull, University of Maryland, Baltimore County; Yevgeniya V. Zastavker, Franklin W. Olin College of Engineering; Rovani Sigamoney, UNESCO

Tagged Divisions

International

theworld have engaged in conversations to bring more awareness to to both sets of ideals.In September 2017, UNESCO convened the Kick-off Meeting for their “Engineering Report II”in Beijing, People’s Republic of China. The meeting was co-sponsored by the InternationalCentre for Engineering Education (ICEE), under the auspices of UNESCO (Category 2) based atTsinghua University in Beijing. The center has been affirmed by the president of the ChineseAcademy of Engineering. Content of the meeting included discussion of engineering’scontribution to achieving the Sustainable Development Goals (SDGs). Several disciplines can beinvolved with plans to achieve outcomes related to the SDGs, however, participants in thismeeting were particularly interested in

Conference Session

Cooperative and Project-based Global Learning

Collection

2018 ASEE Annual Conference & Exposition

Authors

Soondo Kweon, Southern Illinois University, Edwardsville; Jun H. Park, Tongmyong University; Kookhyun Kim, Tongmyong University; Kee Joo Kim, Tongmyong University; Jeonghoon Song, Tongmyong University; Hooi-Siang Kang, Universiti Teknologi Malaysia; H. Felix Lee, Southern Illinois University, Edwardsville

Tagged Topics

Diversity

Tagged Divisions

International

inter- est is in 3D modeling and applications, CAD/CAM/CAE, manufacturing system design and planning, and computer simulation and OR. He renovated the industrial and manufacturing engineering curriculum with introduction of CAD/CAM/CAE and 3D modeling applications to manufacturing systems, and has taught Boeing engineers on the subjects for about 20 years. He was a recipient of NSF grants on developing a supply-chain manufacturing system and on developing an integrated design-aid tool for flexible manufac- turing systems, and of AHA (American Heart Association) grant on volumetric assessment of epicardial adipose tissue using echocardiography . He authored a book on CAD on Unigraphics: Engineering De- sign in

Conference Session

Cooperative and Project-based Global Learning

Collection

2018 ASEE Annual Conference & Exposition

Authors

David W. Gatchell Ph.D., Northwestern University; Akinniyi Adediran Osuntoki Ph.D., University of Lagos; Akinwale Oladotun Coker P.E., University of Ibadan; Matthew R. Glucksberg, Northwestern University; Tania Douglas, University of Cape Town; Kara M. Palamountain

Tagged Divisions

International

(and, in this case, visiting faculty)learn and apply the design process to develop a solution to unmet needs found in a localcommunity in Cape Town and/or brought from Nigeria, respectively. The needle disposaldevice described below was designed and developed by a group of visiting faculty from UIparticipating in this training program during the winter of 2017.Training opportunity – UI and UNILAG, NigeriaFrom 2013-2017 faculty from all four of the collaborating universities on this grant have metin Nigeria (alternating yearly between Lagos and Ibadan) for a week-longconference/workshop to plan the goals for the year, present on the past year’s work, and toplan deliverables of significance for the grant. During the F’16 event hosted by UI

Conference Session

Global and Intercultural Competency

Collection

2018 ASEE Annual Conference & Exposition

Authors

James Warnock, University of Georgia; Galyna Melnychuk, Mississippi State University

Tagged Topics

Diversity

Tagged Divisions

International

Paper ID #22042Development of Students’ Intercultural Knowledge and CompetenceDr. James Warnock, University of Georgia James Warnock is a Professor and founding Chair for the School of Chemical, Materials and Biomedical Engineering at the University of Georgia. He has been a big proponent of self-directed learning and active learning in his classes. James is also the Adjunct Director for training and instruction in the professional services department at ABET. In this role, he oversees the development, planning, production and imple- mentation of the ABET Program Assessment Workshops, IDEAL and the assessment webinar

Conference Session

Humanitarian and Sustainability in a Global Engineering Context

Collection

2018 ASEE Annual Conference & Exposition

Authors

Rosanna Yuen-Yan Chan, Chinese University of Hong Kong; Cecilia KY Chan, University of Hong Kong; Mehrdad Tahernia, Chinese University of Hong Kong; Jiaxin Liang, Chinese University of Hong Kong; Qi Cao, Chinese University of Hong Kong

Tagged Divisions

International

human information interactions and be able to apply them in explaining various techno-societal phenomena. 2. (Learning Outcome 2) be able to analyze and interpret social media contents and social network structures. 3. (Learning Outcome 3) be able to understand their professional responsibility in sustainable development as information engineers. 4. (Learning Outcome 4) be able to understand the impact of information engineering solutions in a global and societal context. 5. (Learning Outcome 5) be able to stay abreast of contemporary issues and formulate professional recommendations and/or action plans based on human information behaviours.The course spans 14 weeks and is focused on 4 topics (Table 1

Conference Session

Study and Research Abroad

Collection

2018 ASEE Annual Conference & Exposition

Authors

Kirsten A. Davis, Virginia Tech; Yousef Jalali, Virginia Tech; David B. Knight, Virginia Tech; Vinod K. Lohani, Virginia Tech; Rolf Müller, Virginia Tech

Tagged Topics

Diversity

Tagged Divisions

International

influenced theoutcomes for students, and that international experiences tended to be more intense [23]. In ourcomparison, the China program provided more cultural intensity, but both programs seem tohave provided research intensity (i.e., opportunities to be challenged and develop). However, thecultural experience may have outshone the research challenges for the China participants, as theycertainly focused more on those topics during their interviews.Both IRES programs have several more years remaining, and we plan to continue collecting datafrom both programs. As we build up a larger pool of participants across years, we will alsoexplore the results of the pre/post surveys for cultural intelligence that we have administered. Weare curious to see

Conference Session

Building and Engaging Communities for Scholarship, Advocacy, and Action for Diversity, Equity, and Inclusion

Collection

2018 ASEE Annual Conference & Exposition

Authors

Janet Callahan, Boise State University; Stephanie Farrell, Rowan University; Adrienne Robyn Minerick, Michigan Technological University

Tagged Topics

ASEE Diversity Committee, Diversity

Tagged Divisions

International, Minorities in Engineering

sessions suchas panels, round tables, workshops and training sessions such as Safe Zone training. The ADChas a vision, mission and published strategic plan, [2] and is an entity to which authors candirectly submit papers.The development of, and institutionalization of the Best Diversity Paper award within ASEE wasa major undertaking that required drafting of the process for soliciting and identifying bestpapers, judging them on a consistent rubric, and disseminating the top papers. The ASEEDiversity Committee crafted a proposal, vetted it internally, worked with ASEE IT staff tocustomize the paper handling system, Monolith, and then vetted with the ASEE Board ofDirectors. The ASEE Board of Directors approved the award and institutionalized it as

Conference Session

International Engineering Education Poster Session

Collection

2018 ASEE Annual Conference & Exposition

Authors

Victor Taratukhin, SAP America; Yury V. Kupriyanov, SAP ; Chris Welch Ph.D., International Space University; Valentina Anikushina, SAP SE

Tagged Topics

Diversity

Tagged Divisions

International

assessment of the deliverables by the jury 10In the very near future, SAP University Alliances/Next-Gen plans to organize further hackathons ondifferent topics to help young talents enrich their theoretical education with practical experience.5. References: [1] Welz, B., Rosenberg, A. (2018): SAP Next-Gen. Springer [in press] [2] Brown, T. (2008): Design Thinking. Harvard Business Review, 84-92 [3] Mabogunje, A., Sonalkar, N., Leifer, L. (2016): Design Thinking: A New Foundational Science for Engineering. In International Journal of Engineering Education. 32 (3): 1540-1556 [4] United Nations Office for Disaster Risk Reduction. UN

Collection

2018 ASEE Annual Conference & Exposition

Authors

Monica Gray P.E., Lincoln University

Tagged Divisions

International

countries. When equivalent experiences were not possible, substitutes were made and theresearch plan adjusted accordingly. For example, for the food production comparative research, asnack factory in Pennsylvania was toured while a brewery in Trinidad facilitated students. Theresearch was adjusted to focus on sustainability strategies around waste and water at bothcompanies. There were potential barriers such as: students having never travelled, did not havetheir passport or proper documentation to get one. The provision of scholarships for the abroadexperience helped to offset the cost for obtaining required documentation. In addition, due totravel inexperience, family members needed reassurance of the benefits of the program as well asthe

Conference Session

Global and Intercultural Competency

Collection

2018 ASEE Annual Conference & Exposition

Authors

Mauricio Torres, Northern Kentucky University; Morteza Sadat-Hossieny, Northern Kentucky University

Tagged Topics

Diversity

Tagged Divisions

International

Behavioral Sciences, vol. 134, pp. 125-133, 2014.[17] M. S. Rasul, R. A. A. Rauf, A. N. Mansor, R. M. Yasin and Z. Mahamod, "Graduate Employability For Manufacturing Industry," Procedia - Social and Behavioral Sciences, vol. 102, pp. 242-250, 2013.[18] H. P. Jensen, "Strategic Planning for the Education Process in the Next Century," Global Journal of Engineering Education , vol. 4, no. 1, pp. 35-42, 2000.[19] M. J. Riemer, "Communication Skills for the 21st Century Engineer," Global Journal of Engineering Education, vol. 11, no. 1, pp. 89-100, 2007.[20] J. D. Ford and L. A. Riley, "Integrating Communication and Engineering Education: A Look at Curricula, Courses, and Support Systems," Journal of Engineering Education, vol. 92